M44 Wiki
Edit Page
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 5: Line 5:
 
I would first start by playing around with WOT(Wide Open Throttle)(easiest). All this requires is tuning the 70% row. Since 70% is the highest the TPS position on the map that would be WOT throttle.
 
I would first start by playing around with WOT(Wide Open Throttle)(easiest). All this requires is tuning the 70% row. Since 70% is the highest the TPS position on the map that would be WOT throttle.
 
You also have to look at TPS angle for WOT detection. This map just tells the ECU what % throttle will we go into WOT mode? If you look at it you can see that it is mostly 60%. So from 60-3000rpm if your TPS is above or equal to 60% then it will go into WOT mode. When in WOT mode this will add the WOT enrichment values to the fuel calculation.
 
You also have to look at TPS angle for WOT detection. This map just tells the ECU what % throttle will we go into WOT mode? If you look at it you can see that it is mostly 60%. So from 60-3000rpm if your TPS is above or equal to 60% then it will go into WOT mode. When in WOT mode this will add the WOT enrichment values to the fuel calculation.
 
 
 
Before playing with anything I suggest having an accurate boost guage and a Wideband Guage as the ABSOLUTE MINIMUM.
 
Before playing with anything I suggest having an accurate boost guage and a Wideband Guage as the ABSOLUTE MINIMUM.
 
While tuning WOT keep an eye on the AFR(i would try to stay around the low 12's) and if anything gets too lean or you hear any pings/knocks get off the throttle immediately and note the RPM at which it happened. Then go back and either try adding fuel(to WOT enrichment if you are doing a WOT pull, else to VE Part load if you are doing part load tuning/anything under WOT), pulling a bit of timing(again without knowing your MAF reading/ load reading this will be quite hard, but you can try taking a guess by using the RPM you hear ping at, then using that as a lookup in the boost map and seeing what load value you have in that table and you can use that to find the load value in the ignition table) or reducing your boost. Remember to change only one variable at a time so you can see the affects of what you are doing.
 
While tuning WOT keep an eye on the AFR(i would try to stay around the low 12's) and if anything gets too lean or you hear any pings/knocks get off the throttle immediately and note the RPM at which it happened. Then go back and either try adding fuel(to WOT enrichment if you are doing a WOT pull, else to VE Part load if you are doing part load tuning/anything under WOT), pulling a bit of timing(again without knowing your MAF reading/ load reading this will be quite hard, but you can try taking a guess by using the RPM you hear ping at, then using that as a lookup in the boost map and seeing what load value you have in that table and you can use that to find the load value in the ignition table) or reducing your boost. Remember to change only one variable at a time so you can see the affects of what you are doing.
 
If you are having trouble increasing your boost and you dont seem to be seeing anymore boost, you may want to take a look at Max duty cycle for boost solenoid.
 
 
        If you are having trouble increasing your boost and you dont seem to be seeing anymore boost, you may want to take a look at Max duty cycle for boost solenoid.
 
 
This is a map that is TPS vs RPM. Basically this map is just the max the BCS/TCV can work so you dont overboost. It is kind of a safeguard. As you can see in the lower RPM's the max duty cycle is about 30%. Towards the higher load / rpm it is around 90-99% which will allow the car to boost much more. I dont recommend messing too much with this map, the values seem to be pretty good stock. By raising the duty cycle in lower RPM high tps area you really risk connecting rod damage.
 
This is a map that is TPS vs RPM. Basically this map is just the max the BCS/TCV can work so you dont overboost. It is kind of a safeguard. As you can see in the lower RPM's the max duty cycle is about 30%. Towards the higher load / rpm it is around 90-99% which will allow the car to boost much more. I dont recommend messing too much with this map, the values seem to be pretty good stock. By raising the duty cycle in lower RPM high tps area you really risk connecting rod damage.
 
Last but not least. If you can log load(using a vagcom or elm327) and ever go above the end of a table (8.02) it will continue using that slot.
 
Last but not least. If you can log load(using a vagcom or elm327) and ever go above the end of a table (8.02) it will continue using that slot.
 
EX. I have a large 50 trim turbo and by 4500RPM WOT my MAF is maxed which would most likely correlate to over 8.02MS of load. This means that i were to tune the ignition/fuel i would need to tune the 8.02ms column all the way across.
 
EX. I have a large 50 trim turbo and by 4500RPM WOT my MAF is maxed which would most likely correlate to over 8.02MS of load. This means that i were to tune the ignition/fuel i would need to tune the 8.02ms column all the way across.
  +
RECAP:
 
 
        RECAP:
 
 
First step, accurate boost guage and afr guage. I suggest having something to datalog afr, rpm, maf and ign adv at the minimum.
 
First step, accurate boost guage and afr guage. I suggest having something to datalog afr, rpm, maf and ign adv at the minimum.
 
Start with WOT tuning as this is the easiest approach(since tuning part load on the street would require holding the car at a steady rpm/load which is extremely hard).
 
Start with WOT tuning as this is the easiest approach(since tuning part load on the street would require holding the car at a steady rpm/load which is extremely hard).
Line 23: Line 17:
 
If you max your MAF / go over the max load on the table (8.02) use that column to tune.
 
If you max your MAF / go over the max load on the table (8.02) use that column to tune.
 
If your finding you cannot reach desired boost and keep increasing requested load and you dont see any changes try playing around with max duty for boost control solenoid. Remember dont go too crazy on this map! You risk bending rods at low RPM high TPS.
 
If your finding you cannot reach desired boost and keep increasing requested load and you dont see any changes try playing around with max duty for boost control solenoid. Remember dont go too crazy on this map! You risk bending rods at low RPM high TPS.
 
In conclusion, M4.4 boost control algorithm is pretty solid. But for people who are looking more to set specific boost and specific RPM / tps a electronic boost controller is probably the best option and a hell of a lot easier to tune as you can set PSI. Then after that all that is left to do is adjust fuel and ign. But again datalogging will greatly help.
 
 
       In conclusion, M4.4 boost control algorithm is pretty solid. But for people who are looking more to set specific boost and specific RPM / tps a electronic boost controller is probably the best option and a hell of a lot easier to tune as you can set PSI. Then after that all that is left to do is adjust fuel and ign. But again datalogging will greatly help.
 
 
Hope everyone has benefited from this and can start tuning their own cars with this info.
 
Hope everyone has benefited from this and can start tuning their own cars with this info.
 
If anyone is interested i can try and go into some more detail tomorrow about part load tuning. This will be useful when easing into the throttle up to WOT to try and control traction issues that may arise without going stupid lean and blowing up your motor. Again this is more complex and will require some data logging tools, which i will be more than happy to go into detail about!
 
If anyone is interested i can try and go into some more detail tomorrow about part load tuning. This will be useful when easing into the throttle up to WOT to try and control traction issues that may arise without going stupid lean and blowing up your motor. Again this is more complex and will require some data logging tools, which i will be more than happy to go into detail about!
Please note that all contributions to the M44 Wiki are considered to be released under the CC-BY-SA
Cancel Editing help (opens in new window)